Overview

VIA IVT01 Android Tablet

The VIA IVT01 is an 8.0″ tablet with Android™ and an FHD capacitive touch screen. It is powered by the 2.0GHz MediaTek500 octa-core processor with 4GB LPDDR4 SDRAM and 16/32GB eMMC storage.

Measuring just 218mm (W) x 37mm (H) x 145mm (D), the system integrates a set of I/O features through the side panel, including USB 2.0 connector, Micro SIM card slot, 3.5mm audio jack, and connectors to support CAN, RS-232, GPIO and power input.

Contact us to learn more about the comprehensive range of services we offer for accelerating the design, development, manufacturing, and deployment of leading-edge in-vehicle systems and devices.

Datasheet

VIA IVT01 8.0

Model Name	IVT01
Processor	MediaTek i500 octa-core Processor - 4 Cortex-A73 @ 2.0GHz - 4 Cortex-A53 @ 2.0GHz
System Memory	4GB LPDDR4-2400 DRAM
Storage	16/32GB eMMC Flash memory
Graphics	ARM Mali-G72 High Performance GPU • 3D graphic accelerator capable of processing 2400M pixel/sec @ 800MHz • OpenGL ES 1.1, 2.0, 3.0, 3.1 • Vulkan1.0 • OpenCL ES 1.1 full profile
Video Decoder	1080p@30fps H.264/265
Video Encoder	1080p@30fps H.264
DSP	Cadence Tensilica Vision P6 x2
PMIC/Audio Codec	- MediaTek MT6358 - Over current and thermal overload protection - Under voltage lockout protection
Wireless Connectivity	- MediaTek MT7668 supports integrated Wi-Fi and Bluetooth - SIMCom SIM7600JC-H MiniPCIe Module
MCU	STMicroelectronics STM32F103RCT6 ARM Cortex-M3 MCU with 256KB Flash, 72MHz CPU
Display	8.0" FHD, 1920x1200 TFT LCD with LED Backlight, MIPI DSI interface
Audio	Nuvoton NAU8223 Stereo Filter-Free Class-D Audio Amplifier
GPS	- Locosys MC-1612-DG Dead Reckoning and Multiple GNSS with ADR/UDR Auto Switch Function
Sensor	- Victory OP T348 3mm Round Ambient Light Sensor - InvenSense ICM-20948 Low Power 9-Axis MEMS MotionTracking Device
Front Camera	CMOS FHD Camera Module
USB	- TI TS3USB221 High-Speed USB 2.0 (480-MBPS) 1:2 Multiplexer/Demultiplexer Switch with Single Enable - SMSC USB2514BI USB 2.0 High Speed 4-Port Hub Controller
UART	Silicon Labs CP2108 USB to Quad UART Bridge Controller
Onboard I/O	- 1 2W speaker - 1 Built-in microphone - 1 MIPI DSI connector - 1 MIPI CSI-2 connector - 1 Touch screen connector - 1 MiniPCIe slot (supports USB 2.0 host only) - 1 Debug UART connector (supports TX/RX) - 4 IPEX connectors (for internal RF antennas for Wi-Fi, 4G and GPS)
Coastline I/O	- 1 x Connector to support: • Power Input (ACC/IGN/BAT(DCIN)/GND) • 1 CAN • 5 GPI and 1 GPO - 1 x Connector to support: • 2 RS232 (TX/RX/CTS/RTS) - 1 x USB 2.0 host 4-pin connector (software controllable) - 1 x Micro-SIM connector - 1 x Reset switch - 4 x Touch key (on Touch screen) - 1 x 3.5mm phone jack (supports Headphone-out and MIC-in)
Watchdog	Supports Watchdog Timer
Power Supply	- DC 9~36V with 36W - Support intelligent vehicle power management: ACC/IGN on/off delay and power protection - Support Input Over Voltage Protection and Short Voltage Protection
Software Compatibility	Android 10 with preload GMS
Operating Temperature	-10°C ~ 60°C
Vibration Loading During Operation	Meets Japan government (MLIT) standard requirements
Dimensions	218mm (W) x 37mm (H) x 145mm (D) (8.58" x 1.46" x 5.71")
Compliance	Pre-scan for CE, FCC Class A TELEC